About Us

Services

Our experience in Electrical Engineering includes the calculation and design of the following electrical equipment and systems:
Electrical equipment:
  • LV Motor Control Centers and Low Voltage Switchgears
  • Low Voltage Cables
  • Medium Voltage Cables
  • Distributor Transformers
  • Power Transformers
  • Medium Voltage Switchgears
  • Variable frequency drives
  • Earthing protection system & lightning protection systems
  • Lighting Systems
  • Diesel Generators
  • Capacitors Banks
  • Uninterrupted power supply (UPS)
  • DC Systems
  • Gas-insulated substation (GIS)
  • Scadas
  • Fault monitoring System
  • Currents Transformers
  • Generators; With gas turbine up to 450 MW
  • Generators Circuits Breakers
  • Bus Duct (Segregated, Isolated , Non-Segregated)
  • Excitation system of synchronous generator
  • MV & HV Grids
  • Power Subestations
  • Smart Grids
Electrical Calculations:
  • Load Balance
  • Load Flow (with different operating modes)
  • Medium Voltage Cables
  • Low Voltage Cables
  • High Voltages Cables
  • Short Circuits
  • Reactive Power Compensation
  • Calculation of Harmonics
  • Earthing protection system IEEE 80
  • Lighting Systems (Dialux & Tekton 3d)
  • Motor Starting Analysis
  • Transient Stability
  • Selection Current Transformer
  • Sizing of electrical equipment
  • Sizing Cables Trays
Principal Documents:
  • Technical Specifications
  • Data Sheets
  • Bill of quantities
  • Design Drawigns Electricals: Unifilar & Developments Drawings
  • Root Trays Drawings
  • Construction Interconnection Templates
  • RFQ (Request for Quotation)
  • BIM Design
Our experience in I&C consulting includes the use of the following equipment and documents:
  • Definition Control Architecture
  • I/O Signal list
  • Instruments List
  • Control and Instrumentation philosophy
  • Local communication panels Drawings & Junction Box
  • Buses calculations
  • Ethernet Networking Design
  • Profibus Networking Design
  • Foundation Fieldbus
  • Hardwired Networking Design
  • Instrument hook ups (Pressure)
  • Instrument hook ups (Level)
  • Instrument hook ups (Temperature)
  • Instrument hook ups (Flow)
  • Instrument hook ups (Analysis)
  • Operator Control Interface
Equipment:
  • Specification Data Sheets Automatic control stations
  • Pressure gauge
  • Magnetic flow meter
  • Pressure transmitter
  • Float level switch
  • Capacitive & conductive level switch
  • Turbidity analyzer
  • DCS
  • Scadas
  • PH analyzer
  • Redox analyzer
  • Turbidity analyzer
  • Conductivimeter
  • NO3 analyzer
  • Rotameter
  • Oxygen analyzer
  • Flow switch
  • Switch pressure gauges
  • Ultrasonic level transmitter
  • Hydrostatic Pressure Level
  • H2S analyzer
  • Organic Carbon analyzer
Principal Documents:
  • Technical Specifications
  • Data Sheets
  • Bill of quantities
  • Design Drawigns I&C and Developments Drawings
  • Root Trays Drawings
  • Construction Interconnection Templates
  • RFQ (Request for Quotation)
  • BIM Design
Our experience with various Installations includes the consultancy of the following services shown:
HVAC General System
  • Heating: adding thermal energy
  • Cooling: removing thermal energy
  • Ventilation: renovation de air and diluting gaseous contaminants
  • Air movement: circulating and mixing air for proper ventilation and thermal energy transfer
  • Central Plan Heating and Cooling Systems
  • Temperature Control Systems
  • Radiant In-floor Heating Systems
Piping & Plumbing Services
  • Propane gas piping
  • Commercial plumbing systems design
  • Natural gas piping systems
  • Compressed air equipment and piping design
Services Water System
  • Industrial Potable water System
  • Central domestic water heating plant design
  • Commercial domestic water and hot water systems
Chemical Dosing:
  • Design Package Plants
  • CO2 System
  • Hypochlorite System
  • Aluminum (liquid and powder)
  • Ferric chloride
  • Lime (hydrated and quicklime)
  • Caustic soda
  • Sulphuric acid
Firefighting:
  • Firefighting facilities
  • Fire safety and evacuation of building
  • Building evacuation scheme
  • Fire Alarm and Detection
  • Automatic Fire Alarm Service
  • Automatic fire extinction Service
CCTV and Security
  • CCTV and security at industrial plants
Method statement for construction
Risk assessments for Construction
Our experience in civil engineering includes the calculation and design of the following facilities and infrastructures:
Raceways:
  • Buried
  • Aerial networks
  • Water supply networks
  • Planbing networks
  • Electrical network
Supporting structures:
  • Rack of electric trays
  • Frames structure
Foundations:
  • Concrete decks
  • Foundation slabs
  • Deep foundations
Enclosures:
  • Concrete blocks
  • Metallic
  • Sandwich panel
Covers:
  • Traditional passable covers
  • Inverted covers
  • Metallic gable covers
  • Metallic in water
Concrete slabs:
  • Manufactured on situ
  • One-way slabs
  • Alveolar plates
  • Steel plates slabs
Main documents:
  • General drawings
  • Detail drawings
  • Spreadsheets
  • Technical specifications
  • Calculation report
  • BIM design
  • Measurements
  • Others
Pre-coordination of pipes.
Pre-design of pipe rack and access platforms.
3D routing in BIM model of both primary and secondary piping systems.
  • Routing of both high and low steam systems, steam drains.
  • Routing of fuel system.
  • Routing of feedwater system.
  • Routing of cooling water system.
  • Routing of utilities system.
  • Buried nets.
  • Etc.
Isometric deliverables.
Pipe stress analysis calculations.
Calculation and design of structural supports for pipelines. Elaboration of catalogue of standard supports, and special support drawings.
Pipe and support coordination drawings.
Deliverables about MTO pipes and supports.
Deliverables about plant disposition of piping systems.
3D modeling in BIM of equipment and tanks.
3D Models Review (accessibility, interferences, good practices, etc.).
  • Supervision of piping and equipment design.
  • Review of supplier drawings and mechanical specifications.
  • Supervision of deliveries of isometrics and pipe supports.

 

Business ethics

MEP PROJECTS is a company of electrical engineering, mechanics and piping in continuous expansion, with great variety and quantity of projects carried out in electrical, civil engineering, instrumentation and control, architecture and software development (IT). Through effective solutions that guarantee the success of the project.

The objective of MEP PROJECTS is to propose to our clients, solutions adapted to their needs, to their industries and business policies. Solutions that begin in the design of their new production plants, or in extensions of the same, reforms and legalizations, and even in a fundamental point within any business sector such as the IMPROVEMENT OF PROCESSES, working under the logo of innovation in services as one of the fundamental axes of the development of our activity.

MEP PROJECTS, recognized for being a benchmark for the quality of its service and the technical solutions provided, both in industries and in buildings in which it specializes, works to strengthen, day by day, this consolidated base of loyal and satisfied customers. wide.

MEP PROJECTS intends to continue to be the expert services company of ENGINEERING and CONSULTING in the Industrial Sector, contributing to our clients, the added value of services of great demand and innovation, such as PROJECT MANAGEMENT and IMPROVEMENT OF PROCESSES (REENGINEERING or REDESIGNING). All this, under the dedication, comprehensive and personalized attention that differentiates us to meet the needs and concerns that each client transmits to us from their business.

We have some solid principles that govern our day to day:

  • Social and environmental responsibility
  • Excellence in project development
  • Fellowship, motivation and personal development
    Business ethics
  • Strong commitment to the client
  • Respect for the intellectual property of our clients